wxbxt78: i cant even start mine up is there something i need to do i really need
help my son just wants to fly it
Harold Vocker: Are the 9116 and 9117 landing skids interchangeable
stevejill91: Do you have the specifics for the servo arm kit for the 9117. I tried to
locate them by c201 but nothing comes up/ thanks
Brian Patterson: You can leave the swash links connected to the swashplate when removing
from servo spline and leaving the helicopter on keeps the servos in
neutral,so that you can adjust without having to worry bout where the swash
will end up when you turn it back on.Just make sure you have both the heli
and controller on while doing this.When you feel that you have it adjusted
well then move the elevator up and down to make sure the swash end up back
in the same place.Then adjust the tie ends for fine tuning
rkjer: Can you help me? Every time I turn off my remote the trim settings reset.
How do I save them? I am just doing it manually with the trim buttons
Seng Lee: So do you need to adjust the remote to make it fly? Please help.
David Harrelson: And also a motor I can upgrade to And a battery pack I might like
Theresa Mayfield: Can you show me how to set up my transmitter on video 9117. I need more
information on 9117 transmitter. Need to see how your transmitter is set
up, having problems setting up mine. The heli just takes off and spins to
Theresa Mayfield: what is the setup for aile d/r and aile /rev. rudd/rev,elev/rev sub/aile
r/l and sub/rudd
ricardopr54: Where did you get your heli? (the 9117) ...and how much did it cost? I was
looking for it at Amazon, but they don't have it yet. I will definitely get
one of those as soon a they become available through Amazon. I like their
return policy in case the heli comes defective.
timw1959: Banggood.com has them for just over $100..It's where I got mine,but it's
TheBeatSmith: I have a 9116 and I didn't notice that my elevator controls were
reverse....holding the elevator down makes the copter fly forward. thats
not right, is it? Can it be reversed.
Timothy Rego: In other words don't buy the 9117 heli, too many things to replace.
LieutenantDanHere: Hey can I use a 9116 PCB board in the 9117? It looks the same. Even has
same numbers on it. Only difference I saw was the 2 screw holes are in diff
place. Let me know your opinion.... Thanks!
Brian Patterson: I would like to thank the people that take the time to make these videos.
If not for them, I'd just got it out of the box,flown it and realized that
I bought a lemon!No wonder this heli has so many bad reviews,because people
don't take the time to research you tube mods you can do to it.Then they
complain about how bad it performs.So thanks again researchers for the time
that you all have put in,so I now have a better understanding of my 9117
MANY PROPS TO YA!! HAPPY FLYING!!
Brian Patterson: These are very nice helicopters.They fly very well, if you take the time
and watch these videos and take your time on every little detail of setting
them up. The only thing that needed serious adjusting on mine,was the
swashplate. When you get it out of the box and charge it,cut it on,then
turn on controller. You will then see how bad the swash needs adjusting.
That being said,make sure the trim on everything is neutral. Then take the
servo arms loose from servo and adjust accordingly. Have fun
Joske de poske: Een dikke Amerikaan is niet altijd een slimme Amerikaan!! Mijn God ,en niet
alleen mijn God maar ook de zijne ,wat een lompe boer.Koop gewoon een echte
dan hoofste je niet te schroeve esse unne gek.!!
TheBeatSmith: Anyone know what it means epa means on the 9116 transmitter...
David Harrelson: And also if u have any suggestions on a motor I can upgrade to and battery
Heli Fan Ensenada: Hi, Can the 9116 and 9117 use the same Tx?
timw1959: I'm useing a 7.4v 2200 25C battery which works VERY well.Thank you.
clancymanone: I hope you don't mind butt I need some help, I am having a problem with my
9117, The video illustrates what is happening, any advice you can give
would be very much appreciated, thanks . Gerry see Video. Help - Double
Horse 9117 - RC Heli Problem
Bryan Botbijl: To increase swash plate movement & the agility of the heli the swash plate
needs to me modified as well. The limiting factor is not the servo but the
plate binding on the shaft. To fix take a drill bit and by hand turn it
inside the swash plate shaving down the square edge increasing the angle
that the plate can tilt in all directions. My 9116 is modded a pro 180
motor & 1200mah 25c Lipo. It is insanely fast now @ 40 mph and can fly easy
in windy conditions.
Brian Patterson: Can anybody suggest a higher rpm motor and battery combo, I mean like some
top notch stuff that the board will handle. I wouldn't want to overload the
control board.This seems to be the only issue I have to complain
about.There's just not enough power for her size. Thank's to all!!
A Printezis: Which one do you think flies better outdoors? the 9117 or the 9116? Bigger
is not always better when it comes to wind i am guessing ! What do you
think? (since you have both?) .. i am thinking of buying of the two.
David Harrelson: Hey I was wondering if u could please do some videos on the helicopter
remote? See I have the 9116 heli and it works great but the instructions
are confusing and I what to know what ALL the stuff on the remote means. Do
u think you can do a video or two of how this helis remote work.
Jaime Guerrero: I was completely lost with the TX when I got my 9116. I found this when
looking for TX info. It's on rcgroups.com Search this....... read
dh9116_tech_manual.pdf It has really easy to follow instructions on the TX
as well as setting up the 9116 itself. I used the info on this video as
well as the info on rcgroups....lots of great info. Hope it helps.
Power Dyne: The Tx manual trim settings do not save. However, you can configure the sub
trims and end points on both high and low speed modes, and they will save
to memory. When you finish in the menu, just hold the menu button for two
seconds. Turn the radio off, then re-bind to the heli.
Double Horse 9117 & 9116 RC Helicopter Setup4.6
out of 5