Brian Wynn: Too much gas bud run it closer to 10
Moffa Hoffa: Why don't you ground to your table?
DAVID TUTTLE: You said your welder was set up for 14 gauge is that what the steel was or
just a setting that worked well?
jason hullihen: 90 degree's man you misspoke your directions man..
Jerrythe coo: Very nice Dony............. A nice compact unit.
jibba02: use a square not a level..
Hai Tran: Thank you for your welding cart video...I finally built my welding cart
using my Hobart 140...
Nima Eghtessadi: Do you think this is better than the one you buy at a retail store?
unclefrankonap1953: just a great job you do anice job explaining projects thanks so much just
subscribed to your channel put have seen lots of your video,s.
donald laisure: Like your cart have you thought of turning your mig into tig welder
donyboy73: thanks dude
RedneckMachines: Try sparks in your shoes those can hurt
Rattletrap2: I am near Shelburne / Orangeville. I can't find part 4. Have you posted it
donyboy73: i would recommend saving ur money to get a name brand mig welder
donyboy73: send me pics when ur done
Nick R: Hey Don. You can turn the shield gas a litlle lower. As long as the weld
doesnt bubble up or get real dirty your good. Otherwise its a waste of
expensive gas. But when its windy you have to turn it up a little. ;)
76chyanne: if you just cleaned it and you have tried adjusting your high ,low ,it may
be time for a rebuild kit the diaprham and pump side of carb,sometimes they
can be damged ,but take your time and try adjustments screw in all the way
then out 1 andthen .25 if its dieing shes not geting fuel,if all else fails
,air may be the compert a leak gasket ,well hope it helps post a vid and
send us a link of ur machine have a good one
savagenomore: don't know what he's using but I use 80/20 since that's what the shop
recommended for general welding of stuff like this, I think they said if I
was welding thin steel I need a higher argon content but that was several
years ago so I might be wrong..
Benjamin Phillips: go with 25/75
AdirondackNY: boy you take a lot of pride in your work, so far this cat looks great
donyboy73: @scuffieduffie thanks!
phonebluejob: Very impressed!!! Dony you should fly to China and give them a tutorial on
how to make stuff that lasts How much was that square stock per foot?
donyboy73: i wouldn't
outdoorsman310: the bottles are very expensive.
donyboy73: good idea!
Born2breakshit: make sure the mig welder has a 100% duty cyle
donyboy73: it's 75% argon and 25 % co2 the welding supply shop will know
donyboy73: yes, where are you from?
donyboy73: thanks for watching
archangel20031: Ok, I'm not even 3 minutes in and what is with the weld flash between
scenes? We see enough of that when we are welding.
theweirdthings: What gas mixture you running at with what wire?
donyboy73: thanks for watching
charger334: hey dony i was wondering what's the best deal on a mig welder to get for a
flagsway: good one
donyboy73: yea that would burn too, lol
donyboy73: i wanted both my welders in one setup so this was better for me
TheCanadianYetii: how much did it cost in all?
famasmaster2000: Hey Don, that cart is looking great already.....congrats. Just as a note
when you get some spare time, you should check out the youtube
channel:weldingtipsandtricks. The guy has awesome vids like yours with
great camera angles and super informative. Just as info bro. Keep up the
good work !!!!
theweirdthings: Do you know what the mixture of gas is? Like 25% argon and 75% co2? Or a
50/50 mix? Just like to know cause those are nice welds and I would like to
set my mig up for gas.
dutchlawnmowerman: nice welding don, i have a little stick welder, but im thinking about
buying the cheapest mig welder i can find. Sander.
donyboy73: yes, his name is brendan...lol, did u pick out a bike yet?
donyboy73: both but mostly circles with the mig
pwleppa: I hope you realize that you are a happy man for being able to do all the
work you are doing. You have skills for many jobs including these YouTube-
videos. Have a nice Sunday. Waiting for part 2. -pw
TXEOC: dude when you open the valve on your tank DONT stand in front of it (its
got up to 2,000 PSI on it) be behind it and open it very slowly!!! adjust
the flow with the regulator valve red numbers 20 no wind 30 with wind
outdoorsman310: how much was the mig welder?
savagenomore: at 3:11
theweirdthings: Theres a certain mixture of ga though, like 75%-25% co2/argon you know?
Carl Bryson: the welding sure is bright in the video lol
theweirdthings: What would 75 co2-25 argon weld like and how much would a small bottle like
the one in the video cost?
How To Build a Welding Cart For A Mig & Stick Welder Part 1/44.9
out of 5