1994 Mazda MPV Timing Belt Replacement, 6 Cylinder DOHC 3.0




People Who Liked This Video Also Liked

1994 Mazda MPV timing belt replacement. 6 cylinder DOHC 3.0
1994 Mazda MPV timing belt replacement. 6 cylinder DOHC 3.0
1999-03 Mazda Protege timing belt replacement: part 2
1999-03 Mazda Protege timing belt replacement: part 2
1999-03 Mazda Protege timing belt replacement: Part 1
1999-03 Mazda Protege timing belt replacement: Part 1
97 Mazda T Belt
97 Mazda T Belt
Timing Belt & Water Pump Replacement : Timing Belt Replacement: Remove Harmonic Balancer
Timing Belt & Water Pump Replacement : Timing Belt Replacement: Remove Harmonic Balancer
How to Replace the Valve Cover Gasket
How to Replace the Valve Cover Gasket
How To Replace LIFTERS / LASH ADJUSTERS
How To Replace LIFTERS / LASH ADJUSTERS
Mazda 626 - IAC Cleaning Part 1 of 3
Mazda 626 - IAC Cleaning Part 1 of 3
How to Change an Alternator : Removing the Serpentine Belt
How to Change an Alternator : Removing the Serpentine Belt
How to replace O2 Sensor Mazda Protege
How to replace O2 Sensor Mazda Protege
How To Install Replace Ignition Coil Ford Explorer Mercury Mountaineer Mazda 4.0L 91-08 1AAuto.com
How To Install Replace Ignition Coil Ford Explorer Mercury Mountaineer Mazda 4.0L 91-08 1AAuto.com
How to replace valve seals on your engine
How to replace valve seals on your engine
Mazda Protege engine code p0300 repair
Mazda Protege engine code p0300 repair
Front Crankshaft Oil Seal Replacement
Front Crankshaft Oil Seal Replacement
How to set your ignition timing
How to set your ignition timing
Replacing(CPS) Crankshaft Position Sensor
Replacing(CPS) Crankshaft Position Sensor
Z22SE3
Z22SE3
Replacing The Oil Pan Gasket Nissan 1.8L
Replacing The Oil Pan Gasket Nissan 1.8L

Did this video help you?

CortesPictures1: @paulhunter123 dude get over it, that is history, and i have a 1995 mazda mpv as much as a i love classic american muscle cars the mazda was my dads and i need to fix it and use it

Zore Zmith: you might need to buy a new tensioner and line up with timing marks. buy a hanyes manual.

mickeymys691: on the right cylinder head i can turn three times around and its suppose to line up on the marks but it lands at 11 clock but now i turn the leftside and it lands right on the mark and destributer i can point to # 1 and runs rough and missfires and i got the #1 cylinder up tdc please let me know what to do about right cam and the destributer and send me some good pic. of where the destibuter and cam is suppose to be thank u very much

Mike Dixon: you have to take the hydro tensioner out under the lower pulley, compress it with a vise or c clamp until the holes in it meet,stick a pin to hold it down, put it back, line the marks and pull the pin.I dont know how you managed to break the pulley bolt in there because its not suppose to thread into the hole it just slides in.

Travis Sanders: your tensioner is defective. you have to grind some off of the brass bushings so that the bolt that holds it ddown does not squeeze the tensioner its self. After tightening this bolt the tensioner must pivot freely. email me your phone number and I will call you. my email is t8085579058 at yahoo.com

Calcutta151: When you get it runnin, make a vid rippin thru some mud ! Its 4x4 right?

conchim99: my 96 Madza MPV has broken timing belt. Do you know how to put cylinder one back to Top Dead Center? thanks. I'm changing the belt right now

ELCCABRON: also i see something weird with the tensioner pulley you sure you got the richt parts? send me a message to my youtube acount i cans send you instructions and images from mitchel on demand they will help a lot replacing the timing belt one these truck is easy

paul hunter: why do americans buy so much japanese junk. pearl harbour! for gods sake.

unbelievableny: What haapppend to this did u fix it or what?

paul hunter: yeah i know what u mean, im always fixing my dad old BMW. If it was mine id prob have sold it.

christopher19691: thats a single overhead cam a dual overhead cam engine on a V-6 has 4 cams

ELCCABRON: hey i got mitchell on demand i could send you instructions hot to do the timing belt on this mpv a friend already replaced a timing belt in one of these trucks and it was easy

sumapto permono: Good..t

rsarp: Nope it's still sitting there. I've had too much to do to fix it, especially without some help. I did get some advice on pre-tensioning that I will use if/when I get back to it.

uthmanamoni: Man I wish I was nearby I'd lend you a hand. I love these mpv's its been five months I just KNOW you've gotten it fixed by now

tim allen: are you sure its a DOHC im pretty sure is a SOHC

MrUnknownfornow: i have the round distributor cap and i have put the plugs the way it is in the book and it doesnt work. do you know where the plugs go in the cap
Rating:
1994 Mazda MPV timing belt replacement, 6 cylinder DOHC 3.0 3.5 out of 5

Featured Video

How to Insulate Walls


1994 Mazda MPV timing belt replacement, 6 cylinder DOHC 3.0