Tracy Gray: Thanks for the info. It was very very easy. A lot easier then what we
zambo3221: I like your videos on rangers and was wondering if you would do a video on
replacing the door locks. I would like to be able to get a matching set and
install them myself. Thanks again for the videos.
dmkaeding: Thanks for the information! Just replaced everything in about 15 minutes.
Gus Mashensic: Thanks guys! Just what I needed!!
1A Auto Parts: If you have a programmed key then you would need to have another one
programmed key for the vehicle.
1A Auto Parts: We do carry them on our website 1aauto.com 888-844-3393
1A Auto Parts: You may want to try to wiggle the key up and down as you try to turn the
ignition to see if it will turn for you.
Justin Hall: Very helpful thank you
0mcgl: how do you change if you cant turn the key
Sparky Channel: Great video. I'm having the same trouble with my lock cylinder on my 98
Volvo V70. Do you sell the part?
1A Auto Parts: We sell new key lock cylinders on our website Part Number: 1AIMX00066 but
if you have lost the key you might have to have a local locksmith make a
new key for you.
1A Auto Parts: This video will show you how to repair it.
youtube.com/watch?feature=player_embedded&v=j3I2oye8OpQ we also carry the
repair part on our website 1aauto.com Part Number: 1AZIS00008
Krauser: I just replaced the Ignition Cylinder Lock, but the ranger thinks the key
is always open and it doesn't turn on either. Thanks.
1A Auto Parts: it could possibly be not aligned correctly inside the lock cylinder.
1A Auto Parts: It might. If it still dings after you replace the ignition, it may be an
issue with the door jamb switch. Hope this helps you out.
1A Auto Parts: We currently do not carry this particular repair part for your 1998 V70
Volvo. Thank you for asking. At the current time we do not have a supplier
for them. Have a great day! 1aauto.com 888-844-3393
pirylocks: does the new key set have to be programmed to the fords computer?
1A Auto Parts: It was there from the factory. 1aauto.com 888-844-3393
xXashtonXx8885: How much will this cost me?
1A Auto Parts: It's hard to say whether it could or not.
1A Auto Parts: Yes, you would need them to turn the ignition forward. 1aauto.com
yorxs2: Can you user your old keys with the new lock cylinder? I would hate to have
seperate keys for the door and the ignition.
1A Auto Parts: @freakincrap27 The procedure should be the same.
1A Auto Parts: We currently do not have an auto repair video that shows this particular
repair on your vehicle. We'll keep this request in mind in the event that
we need to make this repair in the future.
Joseph Suarez: Will this work for my 1995 ford ranger? My ignition turns on the car but it
will not turn it off. It turns backwards pretty easy.
1A Auto Parts: Have you tried to replace the MAF sensor, that may help you out if the
issue seems to go away once you unplug it.
1A Auto Parts: You're welcome. Have a great day. 1aauto.com 888-844-3393
Frankie Esquivel: My keys were stolen. Do I need to have the key turned on the ignition in
order to remove/replace??
1A Auto Parts: You're welcome. Have a great day! 1aauto.com 888-844-3393
Terry Stamper: I don't have an engine light on, but when the van gets up to 40-45 it
starts to vibrates this goes away when I lightly tap the brake and and
continue to gas up this will continue when the speed levels off, I can
speed up with no problem but when I level off I get the vibration. I unplug
the MAF Sensor the van doesn't do this but the engine light is on with
ocassonial engine stall. I've switched sensors with the same results, the
van seems to run better when the sensor is unplugged
fuckinshit27: whats the procedure fora manual 94 ranger?
bghurk: Great video! Someone stole my car by ripping out the ignition lock. When
they did it, they broke the housing that the lock goes into. Do I have to
pull the steering wheel to access?
1A Auto Parts: The only thing you can do at this point is take your vehicle to someone to
have them replace the lock cylinder. Sometimes once they lock in place,
there is no way to remove them without completely taking the cylinder apart.
Idrissa Ekundayo: THANK YOU!!
zach wasil: awesome videos! i hope my ignition key change goes this easy...i hope i
1A Auto Parts: You may be able to access it like we did in the video.
Zack Cagle: Mine got locked because I didn't relize it would if if it was sticking what
do I do? Soeone tell me please!!
HeemDa Yungin: do you guys have a lock cylinder for a 2000 grand am
pandabear601: What do I do to replace my lock cylinder in my 95 s10 I've lost my key
1A Auto Parts: We currently do not have an auto repair video on this particular year make
1A Auto Parts: We carry new ignition key lock cylinders for your Ford Ranger on our
website 1aauto.com PART # 1AIMX00065 888-844-3393
Jordan Gosnell: having issues: when i put the new unit in, it will not turn to start or to
the off positions. its pre march of 96 ranger so i know i have the right
Monte Walsh: Is the hole in the column trim (where you insert the tool to depress the
pin) made by the factory or did you drill it ? If you drilled it, how did
you know WHERE to drill it.
1A Auto Parts: Unfortunately unless you key the new tumbler cylinder to the old key will
not be correctly and you will have to use the new key provided with the lock
duhawk9000: I have a 99 ford ranger that I cannot turn the key when it is in the
ignition. I was wondering how I would replace the tumbler?
Terry Stamper: Will a sloppy ignition affect the maf sensor I have a 92 Ford Aerostar and
other sources have stated that the sensor could be engaged before the
engine is running causing it to burn out.
1A Auto Parts: There could be several different things. The physical switch could be bad
and causing the computer not realize that the tumbler is bring switched
back.The other thing it could be is the tumbler could be broken and not
rickibirnbaum: Awesome! Thanks guys!
roots8848: Very helpful videos. On my 2000 Ranger, my ignition is getting very hard to
turn. I have to fidget with it to get it turn on. The door open dinging
noise was also acting wierda couple days ago, now it doesn't ding at
all(not that I care). Do you think doing what you did here will fix the
hard turning issue? Seems like the cheapest place to start to me...
How To Install Replace Worn Out Sticking Ignition Key lock Cylinder Ford Ranger 90-96 1AAuto.com4.6
out of 5