Ibrahim MM: hi , i have 3 cables on my E87
Amarouch Lamrini: I have 3 cables on my w212.
White: data cable
Where do I need to put the 2 cables of the bypass?
yanko yankov: i need bypass for 530 e60 2004 year ...
Muhammed sohaib: Wonderful 2 good
jgdran: Do you know of a bypass for a BMW 04 E60?
yanko yankov: Could you give as for bmw e60 2004 year please ?
MultiNerb: worked perfectly for my 2000 BMW Z3!
Joe Creed: you can buy a ready made plug from ebay, £6 and you literally plug it
sonny butt: Hi mate will that work on bmw 520d m sport it looks like its a common fault
richard s: Hi what was the response for the 3 wires I have a bmw mini cooper
George Berling: I did exactly what you said and it kinda works... The airbag light turns
off after 2 min of driving. I was wondering if there is anything you can do
for it to turn off right away?
mexusbg: I didn't needed a reset tool after using this bypass (E46 318is). Just
connected the diode and two resistors and the red light on the dashboard is
megatron851: I have the same three wire setup on 2006 750 E65. Did you ever get an
answer to this question?
Dino Calderon: someone already asked this quetion but i see no answer so I will try and
ask it again. After installing this bypass will it automatically turn the
airbag light off or will we need the reset tool to turn it off ?
japemw: Hello there! I make this connection. Error dissapeared after clearing the
error memory. But then I check with INPA livedata from airbagsystem and it
tells that nobody sits on the passenger seat. I think that the passenger
airbag does not work with this connection.
Edmond hgaquest: I TRIEDTHE SAME THING ON MY 2001 BMW X5 BY FOLLOWING THE SAME (100ohm
RESISTOR, THEY ARE A LITTLE SMALL BUT THE SAME CAPACITY.AND THE DIODE WITH
THE COLORED SILVER GOES TO THE BLUE WIRE, BUT IT DOESN'T WORK ALL. I ALSO
HAVE THE PEAK SR5 16 PIN TOOL TO CLEAR THE CODE, BUT THE AIR BAG LIGHT
COMES RIGHT BACK LESS THAN A SECOND. ANY HELP???
Thalia Baptiste: yes i do, my name is Richard, i have 520I 5 series e39. email
email@example.com 1868 343-5239
BoogityBoogityBoo: do I need the reset tool to turn off the light after installing the bypass?
or will installing actually turn off light?
vehix411: you need seat emulator
evethang: Vehix411, my seat does not have a blue/white wire nor a black box. Mine has
3 wires coming from the seat sensor and plugging into another wire which
goes to a yellow unit under the seat towards the front. Please help as I do
need a bypass for this one. Thank you.
TheOneHawk: Will the same method work for 2004 330xi
peter considine: Worked a treat for my 318 I. Cheers bud
TheyLive WeSleep: if that even happens:, someone would have asked him the question already.
86netsniper: Does it make any difference which side the resistor is/are facing when
connected to the diode?? Thanks.
thainosz: It's serve also to 318TI E36 M44 1997?
carloschickos: I have a 630i 2005, dunno whats causing the lights to stay on, but got air
bag Red and seat restrainer warning , will this do the job?
Adil Akrouh: hi, please how i can make a bypass for BMW 3 SERIES with 3 wires
bmwnasher: Had a diagnostic done it said seat occupancy mat. fitted this had the light
knocked out and after 4 day the light is back up?
Karamveer Dhaliwal: What about the seat belt chime..do u have to keep the passenger seat belt
always buckled ??
christof impreza: what do i need for a bmw 530d e60 2004 ??? it's 2 wired ...
77AD77: i had these two lights on is there any fault in seat passenger or airbags i
have series 5 2006.
georgec83: if i used Resistors 820 Ohm will this work?
Adi Satrio: i have the same problem with my E46 318i, i have 2 pcs 100 ohm resistor,
but i only have a IN4004 diode, can it work?
Cory Malagise: Is there a fix for an e90 bmw. I have a 2006 which means I have three
wires, not two. Bought a bypass on ebay and my car didn't chime, meaning it
didn't think someone was in the seat, meaning it didn't work. any ways to
make my own?
markhelllen: Brilliant. Had to get the light reset but this worked total cost 90c..
Thanks for putting this up. God Bless You!
TheciROCBoyz: Will it work for the driver side?
Edmond hgaquest: ALSO, THE PEAK 16 PIN TOOL REVEALED TWO CODES: (03 & 05) I SEE THERE ARE
MANY OTHER DESCRIPTIONS DESCRIBED BY THE SAME CODES. SO I GOT CONFUSED ON
THAT AND DO NOT KNOW WHAT DO THEY MEAN?
Svillen Atanassov: gotta be kidding me :D
vehix411: Sometimes it reset automatically sometimes you need the tool to do that i
just did a car last week and it turn off automatically
Sammywammy858: Awesome. Works great. Thanks a lot. The mechanic said I need a new seat.
$2.67 in parts. Radio shack. 10 min. Of my time and I finally saw that damn
light turn off. Thanks a mil
mishmash10101: Worst video ever. EVER.
lbsnowboarding: has anyone figured out how to connect this bypass to a three wire.
white(data), brown(ground), red(12v)? What does the blue and white wire
Duwop77: Hello, did you twist the resisters to the diode or solderd them? Thanks
vehix411: it should make the pass airbag active
vehix411: no 100 ohms only
vehix411: this will bypass the pass seat sensor and will tell your airbag module thet
someone is sitting their all the time and should activate your passenger
airbag in an accident
sario22152: what if it activate the air bag??????
bbbd01: I have the brown, red and yellow module...how do I find it and bypass it?
vehix411: try IN4007 mini diode it should take care of that
pauloeadie: Hi Mate, will this method work on an E65 and would I use same size diode /
How to bypass BMW Passenger Seat Occupancy Mat sensor for passenger Airbag4.4
out of 5