How To Remove Jeep Front Axle Shaft Dana 30 / 44




People Who Liked This Video Also Liked

How To Remove Jeep Front Axle Shaft Dana 30 / 44
How To Remove Jeep Front Axle Shaft Dana 30 / 44
RCV Dana 30/44 JK Unit Bearing Axle Installation
RCV Dana 30/44 JK Unit Bearing Axle Installation
Easy Jeep Wrangler Axle Upgrade to Dana 44 TJ Rubicon
Easy Jeep Wrangler Axle Upgrade to Dana 44 TJ Rubicon
89 Cherokee Dana 30 CAD Delete
89 Cherokee Dana 30 CAD Delete
Jeep Wrangler Dana 30 C Gussets Syneregy / Artec Installation Weld In Service Lifted Trucks
Jeep Wrangler Dana 30 C Gussets Syneregy / Artec Installation Weld In Service Lifted Trucks

Did this video help you?

san379: great vid
 check my video from yesterday.. front n rear tj axle shafts slapped.. cone gear worn down in the rear diff.. spider gears busted

Juancho EastEndRiders: Great DIY tutorial...!!! I definitely give a shot this weekend..!!! Question... Do i have to remove the AXLE cover to remove the shaft..?? Thanks in advance!

RANDYS Worldwide Automotive, Inc.: Tech Video Friday (on Thursday)!
We found a great video to walk you through removing the front axle shafts, front axle hub bearings, and u-joints from a Dana 30 or Dana 44.  This video shows just how easy it is to do this project on your own with the right tools.

ANNETTE SCOTT: thanks man

DirtyWade1994: Am I going to have to put gear oil in the differential after I pull out the shaft? Or do I have to pull that to change the u joint any help would be much appreciated 

zip25265: So much help than you to explained it very simply good camera work and I fell like I can do that to mine now thank you 

nightprowlerch19: Hi cody I'm a big fan of the wrangler star channels. I love all your homestead projects . But the DIY jeep stuff hits home for me I have a 2002 Wrangler . I know its a huge ordeal to put together quality videos but I would really appreciate it if you would do more jeep stuff if you have time I understand you're very busy and I don't want to sound like everybody else pulling you and all these directions . I wish the best to you and your family

thehashmonkey: reverse torque bolts ford is notorious for them as well

M. J. Brudenell: I am having trouble getting that plate pried away from the heat shield. I was using a large flat screw driver. Do you have any advice on how to get it worked loose?

Ok Ryan Driskill: Fffff

Richard Jefferson: Do the ends of the front axle shafts have anything locking them in place inside the differential that prevent them from sliding out when the 3 bolts are removed as shown in the video?

Chris Wooldridge: I tried mashing it with a punch too bit it was ceased. There is an easier way. Take those hub bolts and thread them in until the hole is flush with the tip of the bolt. Then take a 9/16 12pt wrench and cover the bolt. Apply the hammer a little and viola its out.

uncleben03: Cherokee XJ's were leaf-sprung in the back, not coil sprung like TJ Wranglers. Cherokee's had Dana 30's up front like the video shows, but had Dana 35, Chrysler 8.25 and Dana 44's in the rear over the years.

Joshua doughty: is there any difference between this year of wrangler and the same years of Cherokee. suspension? and axle?

Autobahn No Limit: Your videos inspires me to begin working on my own vehicles - - - "Commit your work to the LORD, and then your plans will succeed." Proverbs 16:3 - Thanks Cody. Shalom.

hinckleypoland: I am not mechanically inclined... so THANKS! I am learning how work on my jeep. :-)
Rating:
How To Remove Jeep Front Axle Shaft Dana 30 / 44 5 out of 5

Featured Video

How to Insulate Walls


How To Remove Jeep Front Axle Shaft Dana 30 / 44